These racers are illustrating...
These racers are illustrating the correct method for raising the car to facilitate working underneath. They placed jackstands under the car after using the jack to raise it. They then lowered the car onto the jackstands.
Some tools you can do without, while others are a necessary part of your toolbox. Of all the tools required to work on your car, a good floor jack is one of the essentials. Without a good jack, about all you will be able to do at the track is adjust the air pressure in the tires and maybe change a shock. Being able to lift the car off the ground and place a jackstand under the chassis is a minimum requirement for tuning.
Every week we see the NASCAR pit guys use a floor jack that, with two or three pumps of the handle, lifts the car high enough to allow the tires to be changed. Those jacks cost over $1,500, and that is out of the range of most Saturday night racers. If you watch closely, you'll notice the NASCAR guys use a different jack in the garage. These jacks are not as "trick" as the ones used on pit row. But even the jacks used in the garage are not cheap: Prices can range from $500 to $700.
So what does a Saturday night racer need to use in the pits?
Ninety percent of the local racers out there will not be making pit stops during the race. That means the jacks that reach full lift in two or three pumps of the handle are not necessary. To determine our needs, we need to ask a few questions:
* How heavy is your race car? If you have a 3,500-pound car, you need a jack that will lift at least half that weight.
* How many jacks do you need? Is it possible that you will have to work on each end of the car at the same time and that your crew will need two jacks to be efficient?
* Will you have to purchase a jack just for shop use, or will you need one in the trailer and one in the shop?
* How high do you need to lift your car? That is something you will have to measure.
* Is your car low enough to require a low-profile jack that will roll under the car without a crew member lifting the car to get the jack under the chassis?
* Are the pits at your track dirt, or are they paved or concrete? That can determine the type of wheels you want on your jack.
* Is the weight of the jack an issue? If you have to carry it a long distance, this may be a real issue.
* How much do you have to spend? (This may be the primary issue facing most small teams.)
What you see here is close...
What you see here is close to $5,000 worth of floor jacks. These are part of a Nextel Cup team's pit. Only one jack will go over the wall at a time; the others are there in case of failure or if another jack is needed during a pit stop. While these are high-performance jacks, they would represent overkill for the local racer.
This low-profile floor jack...
This low-profile floor jack can be purchased for less than $200. It's lightweight and completely suitable for the Saturday night racer.
This jack was purchased to...
This jack was purchased to replace the author's 32-year-old model. The cost was $119.95, and it seems to work well for our applications.
The good news is that you now have options that were not available several years ago. The marketplace is awash in lightweight floor jacks at reasonable prices. And it's a buyer's market. The jacks on the highest end of the spectrum are just that-high-end, meaning they're expensive and purpose-built. They fill a very specialized need and you can expect to pay top dollar for that type of product. The racers who make pit stops during races really need this type of jack. They command a premium price because of the special need they fill. If the racing you do each week does not require a 12-second pit stop to change four tires and fill the car with fuel, you can look to less costly options for floor jacks.
Historically, floor jacks have been made from steel and cast iron, and these behemoths are heavy. Unless you are especially strong, lugging one around is not an easy proposition. These jacks were designed for heavy industrial and garage operations. They were not designed for racing applications. For years they served the purpose but there was a price to pay due to the weight and the intended application. And they were expensive. Times changed, though, and market forces required a response.
Because of the many automotive TV shows and a general awareness of mechanical hobbies, the tooling manufacturers have responded to fill a new or a different demand. This was a demand not previously being served by the mainline toolmakers. This awareness has placed more racing hardware into the mainstream, and the racer at the grassroots level is reaping the benefits.
The opposite end of the scale....
The opposite end of the scale. This type of jack can be purchased for $20 at the local auto parts store. While not a bad tool, it has no place in a racer's toolbox. There are much better selections.
This floor jack was purchased...
This floor jack was purchased new from Sears in 1976. The author paid $76 as part of a bicentennial sale. Recently, the internal seals started to leak and the jack no longer works well. With proper care, a floor jack can last many years. For much less than the cost to repair the jack, a newer, lighter floor jack can be purchased.
This jack can be purchased...
This jack can be purchased for under $80. There is no reason that any racer should not have an adequate floor jack.
It is now possible to purchase a lightweight aluminum floor jack for a price that ranges from $80 to $199. We can buy a 1,500-pound rated, rolling aluminum floor jack that is a perfect fit for the Saturday night racer.
Now, these jacks don't have the same quality as the specialty racing jacks, but they seem to fill the needs of the Saturday night racer. I have been using one in my shop for the past year with no issues at all. In fact, the racers at the track have been telling me the same thing.
A review of the pits at the local speedway will yield a good number of these lightweight jacks that have already found a home. This supports the concept that the racer can purchase a floor jack that will fill a need and not break the budget. Do not try to jack up a fully loaded race car trailer and change a flat tire, however, because it's not going to happen. But if you need to jack up the front, back, or side of your stock car, they work great.
Where are these jacks available? They can be purchased from many online racing parts vendors. Many of the local auto parts houses around the country sell them as well. For example, Harbor Freight sells a line of aluminum racing jacks.
If you want to get pumped up and carry around a 50- to 60-pound floor jack, you can purchase an all-steel version for about $59. For just a few dollars more you can get a jack that is lighter, easier to move around, and easier on your back.
This aluminum jack can also...
This aluminum jack can also be purchased for less than $200. It is light and seems to be working well on a hard, packed dirt surface.
This aluminum jack is being...
This aluminum jack is being used on a Dirt Late Model. For the Saturday night racer, this family of low-cost aluminum jacks seems to work quite well. They are sturdy enough to put up with the harsh environment that the racer has to deal with on a weekly basis, and the cost is low enough to not put a large dent in the tooling budget.
The uses of floor jacks are...
The uses of floor jacks are limited only by the imagination of the racers who use them. They are a critical part of the tools used to tune the car at the track and work on the car away from the track. A good floor jack should be considered an essential tool for every racer who drives into the pits.